Respiratory Protection EquipmenT
LVTU™ AP Series, a premium range of Disposable Single Use Particulate Respirators
FFP2 Flat Foldable EN149:2001 + A1:2009 Disposable
Half Face Particulate Respirator with valve NR
FFP 2 Key Features
- Ergonomically designed to provide a close fit, flush to the face
- Vertical fold flat design for easy pocket storage
- Individually packed to prevent contamination
- Suitable for vending
- Conforms to EN149:2001+A1:2009 FFP2 NR
- Anti-fog performance
- Exhalation valve for increased breathing comfort
- Secured in place with the LVTU™ head harness
- Unique “V” shaped profile ensures the mask fits the contours of the nose
FFP2 respirators are
recommended for protection
during aerosol generating
procedures and for the
prevention of airborne
infectious diseases.
All LVTU™ AP Series masks fulfil the requirements of
EN149:2001 + A1:2009, the European Standard on respiratory
protective devices requirements and testing procedures.
technical datasheet
FFP2 flat foldable EN149:2001 + A1:2009 disposable half face
particulate respirator with valve NR.
Conformity assessment procedure: Module B
Product Details
| Model Number | LT2020AP2V |
| Description | Particulate Filtering Half Mask |
| Type | FFP2 Flat Foldable Respirator with valve, single shift use |
RECOMMENDED APPLICATIONS FOR USE
Low level fine dust/oil or water based mists (hand sanding,
drilling and cutting). Moderate level fine dust/oil or water
based mists (plastering, cement, sanding and wood dust).| Manufacturing Industries | Agriculture |
| Iron & Steel Industry | Civils |
| Laboratory | Mining |
| Automotive | Quarrying |
| Pharmaceutical | Utilities |
| Dental | Construction |
Precautions
- Protection against solid (dust) particles and/or non-volatile liquid particles. Higher protection levels such as protection against Gases, Asbestos and Silica Dust require a minimum of FFP3 and must be fit tested.
- Always remember that the respiratory protection is only effective if it is correctly selected, fitted and worn throughout the time when the wearer is exposed to hazards.
- It Is the wearer’s responsibility to check whether the correct RPE is being worn against the task and hazards faced.
- Always be sure that the complete product is: suitable for the application, fitted correctly, worn during all periods of exposure, replaced when necessary.
- Proper selection, training, are essential in order for the product to help protect the wearer from certain airborne contaminants.
- Failure to follow all instructions on the use of these respiratory protection products and/or failure to properly wear the complete product during all periods of exposure may adversely affect the wearer’s health, lead to severe or life threatening illness or permanent disability.
- Facial Hair will affect Protection Levels wearer should be clean shaven to insure adequate seal.
PHYSICAL PROPERTIES
| Total Inward Leakage | ≤ 11% |
| Penetration Test of Filter Material | ≤ 6% Sodium Chloride |
| Penetration Test of Filter Material | ≤ 6% Paraffin Oil |
| Inhalation Resistance | @30L / min ≤ 0.7 mbar |
| Inhalation Resistance | @95L / min ≤ 2.4 mbar |
| Exhalation Resistance | @160L / min ≤ 3 mbar |
PRODUCT DIMENSIONS
| Mask Height: 165 mm | Nose Bridge: 100 mm x 10 mm |
| Mask Width 1⁄2 Measure: 110 mm | Valve Diameter: 39 mm |
| Mask Thickness: 2 mm | Mask Weight: 6 grams |
| Head Harness Width: 5 mm |
Material
| Outer Layer | Non-woven Polypropylene |
| Filtration Layer | Meltblown non-woven Polypropylene |
| Padding | Polyester |
| Inner Layer | Super soft non-woven Polypropylene |
| Head Harness | Polyester / Lycra |
| Adjuster | Plastic |
| Nose Bridge | Steel wire band with foam strip |
| Valve | Plastic |
| Filter | Silicone |
Packaging & Storage
| Outer Pack Dimensions | 14 x 14 x 18.5 cm |
| Outer Pack Contents | x20 Respirators |
| Master Carton Dimensions | 46 x 58 x 44 cm |
| Master Carton Contents | x24 outer packs, containing 480 respirators in total |
| Shelf Life | 24 Months |
| Storage Instructions | Keep out of direct sunlight, store in a cool place, temperature limits between -5°C and 50°C. Humidity ≤ 80% |
PRODUCT & MANUFACTURING CONFORMANCE
| Product Standard | EN149:2001 + A1:2009 |
| Manufacturing Standard | ISO 9001:2015 |
| Notified Body | APPLUS 0370 |
| Traceability | Batch Number |
| CE Classification | Category III |
